| BRAND | GIMAX |
| Product | BLGPN1812400 |
| Internal code | IMP4905160 |
| Technical specification | BLG Policarb.3060Lm 18W 24VACDC LED Lamp L=640mm, 50mm, PM16 cable input Lamp composed as follows: OUTER SHELL POLYCARBONATE tube with excellent transparency and shine characteristics. Exceptional chemical resistance to medium-concentration mineral acids, to alcohols with the exception of alcohol methyl, to aliphatic hydrocarbons (oils and fats). The maximum operating temperature for continuous use 100°C. Tube thickness 1.5mm outer diameter 50mm SIDE CLOSURES Side closures in TAROPLAST material (Taromid A 280 MT6) 6.6 loaded at 30% (PA6.6+) 30% F.V.) reinforced with fiberglass (Glow wire test 960°). Each closure is made of two parts separate: the innermost part has the task of keeping the internal screen locked (described below) and incorporates No. 3 threaded brass inserts drowned during molding. The external part is tightened to the internal one by means of 3 through stainless steel screws. At the time of tightening of the closing screws, the seal inside is compressed against the tube, obtaining thus an effective protection against water and dust infiltration. GASKETS BAYER silicone-based O-RING sealing gaskets in red color. Characteristics of excellent heat resistance (250°C), excellent resistance to low temperatures and flexibility in the cold (-60°C). Excellent stability. Excellent resistance to aging and great stability to ozone and ultraviolet rays. Excellent dielectric behavior over a wide range of temperatures. excellent elastic characteristics in the wide range of hardnesses available. Great elongation at break. Excellent dimensional stability. Complies with BGA, FDA, KTW regulations. INTERNAL SUPPORT Reflective aluminum screen for maximum light output, with support function for the drivers and LED modules. In front of the reflective profile, there is an OPALINE anti-glare SCREEN. LED LIGHTING MODULES The modules are essentially made up of multiple LED-type emitters with shapes, dimensions and provisions to optimize luminous uniformity in relation to heat dissipation. the type of coloring adopted, instead of fluorescent lamps with white or very white light normally used, it has a color temperature included in the range 4300÷4500 °K (light very white). Life of 50,000 hours (at 25°C) against 8-10,000 hours of fluorescent tubes or 500-2000 hours of halogen lamps. Completely insensitive to frequent ignition (a factor that significantly limits the duration of fluorescent tubes) Instant ignition (without warm-up times) at any operating temperature (from -30°C to +40°C) with no starting currents (oversizing is avoided power lines or any power transformers Light output of more than 50% of fluorescent tubes because the light emission has an angle of 120° against that of the fluorescent system which is 360°, therefore, all the luminosity is used for illuminate the affected area without dispersion of light into the external environment. This leads to a significant savings in terms of energy consumption while maintaining the same degree of illumination of the affected areas. GENERAL CHARACTERISTICS Insulation class...: II (230V) III (24V). Degree of protection...: IP67 (IEC 529 and CEI 70-1 standards). Marking...: CE The lamp is equipped with: - n. 1 PM16 cable entry, IP68 degree of protection, complete with device tear-proof, placed laterally to a closure. - n. 1 electronic control board: Selected components with high quality standards. Stabilized output stage, in PWM technology, to ensure constant luminous flux even in presence of temporary changes in supply voltages. Complies with EN 60928, EN 61547, EN 61000-3-2, EN 61000-3-3 61000-4-2, 61000-4- 3, 61000-4-4, 61000-4-5, 61000-4-6, 61000-4-11, EN 55015, EN60598-1, EN60598-2-1, EN61374- 1, EN61347-2-3, EN60249-1. - n. 1 LED module consisting of n. 60 LEDs, total power 18W (high efficiency 3060 lumens), Cold white color, color temperature 6500°K, 50,000 operating hours). Operating temperature...: from -10°C to +50°C Power supply...: 24V AC-DC Lamp length...: 640 mm. C.a. |
default.send_request_amp_Group2