| BRAND | Steimel |
| Product | AT1-182040R / T1-60G-GKGM |
| Internal code | ONR4625171 |
| Custom code | 84136039 |
| Technical specification | ATEX aggregate PTFE, GD, EC, AW, G3/4, M37GN/10, M.Ybx469, MR3Z02.0-386 rpm Gear pumps - aggregate: T 1 - 60/G - GKGM according to Directive 2014/34/EU (ATEX) Item number: AT1-182040R Dimension sheet: DPA001-182040R Spare parts list (pump only): DET001-A031R Operating instructions: DBA-ZP02 + DBA-ZP-ATEX-01 Suction and discharge connection: G ¾ Material finish: Housing parts: EN-GJL-250 (EN-JL 1040) Drive and counter pinion: 16 MnCrs 5, hardened straight-toothed Shaft seal: mechanical seal M 37 GN/10+K+R Q12Q1KGG1 Elastomers of the mechanical seal: Kalrez temperature monitoring on the mechanical seals: 1 PTC thermistor (ATEX), BTW062 wired to Ex terminal box, NAT: 100 °C iBexu 14 ATEX 1291X Display device: on-site Bearing Bushings: Bronze AW increased bearing clearance: without Case seal: Loctite other elastomers: PTFE Extraction hole: without Pumped medium: paints and varnishes solvent-based, pigment-containing, max. 100 μm grain size Concentration: 10 - 70% Viscosity: 1,000 - 2,000 mm2/s Temperature: max. 70 degrees C rinsing with solvent (viscosity 30 - 1000 mm2/s) approx. 10% of the passage of time Delivery data: Q: 0 - 300 L/h p: 0 - 3 bar (pump must suck) n: 0 - 250 rpm direction of rotation: right Test run: yes, with HLPD 46 Pre-cleaning: rinse with mineral spirits Base plate: EGP913045-21BB05 base plate with vibration dampers for free installation on indoor floors article - no.: ILW040x30x55und 4x Ø14 Dispatch fixing holes Coupling: BKUP078-1020-001 Clutch protection: BKS918100080AC01 (sheet brass tread resistant) Pad: EUL—032100BB01 plaromaster ball roller gearbox with intermediate gear and motor Make: Planetroll with ATEX - attesting Type: 0.37D2 (Ex) MR3Z02 - 3, 109 - 1 Product no.: LGM037MR3—001 engine data Power P: 0.37 kW output speed n: 0 - 386 rpm Rated speed - motor n: 2825 rpm Voltage U: 230/400 volts Frequency f: 50 Hz Degree of protection: IP 55 Insulation class: F explosion-proof: Ex e II T 3 Design: B 3 Control element:type HVK, analog display, coarse scale 0-12, fine scale 0-100, viewing window at the top ATEX nameplate: Enter control range Paint: RAL 5009 (HDE) Silicone-free pump! The pump was tested with mineral oil and must be flushed on site before commissioning! Sign: EAY924-PL02 Identification plate: ETY924-D-E—PE03 ATEX marking: II 2G Ex h IIB T3 Gb Please observe the provisions of Directive 2014/34/EU (ATEX) regarding the use of our pumps in hazardous areas. Prerequisite for operation according to: Ex zone 1 (gas), temperature class T 3, Ambient temperature -20 to 40°C Explosion group IIB. Attention: Before starting the pump, the temperature monitoring can be connected functionally! |
Press on flag images to see contact information!
