connector kit
HBM Schraubmesswelle, nominal torque 10 Nm with strain gauge measuring system, accuracy class 0.1 built-in rotary encoder Tool Standard connections 10 F / G 10 according to DIN 3121 with 2 fixed mounted connection cables separately for torque u. angle of rotation 3 m long, with free ends
Torque transducer, rated torque 20 NmMesssignalübertragung about SchleifringeDMS measurement system accuracy: 0.1Elektrischer connection via plug introduction of torque on shaft stub (friction) torque output signal 2mV / VNenndrehzahl 4000U / min
Torque reference sensor
Reference torque measuring disc, nominal torque 5 kNm DMS measuring system Accuracy class: 0.05 Permanently mounted connection cable 3m, with free ends Torque transmission via flange Torque output signal 1.5mV / V
displacement transducer
Mitutoyo Mark Magnetblock HBM can not be produced
(load cell Rated load: 50kg Minimum division value: 0.0090% of Emax OIML R60 test report Accuracy: C3 Measuring body: Stainless steel Protection: IP68 according to EN 60529 Cable: Shielded 6-wire round cable with PVC Cable length: 3m)
SUB-D-Stecker
compressive force transducer
Anschlussstecker
8-channel USB measurement amplifier espressoDAQFamilie
including programming the memory contents of the TEDS TEDS Aufnehmersteck module is mounted.
Type HLM-20242 Output 1.8 millivolts load cell
Emax: 2.2 t, Emin: 0 kg, Limit: 3.3 t Vmin: 220 g, Cn; 1.94 mv/v; TC2163
Load cell
cable and connector set. This product contains HK31S-G and 10 m of cable wiring.
(Calibration of the measured variable force in accordance with the HBM standard (without connector assembly). Traceability by DAkkS accreditation guaranteed by ISO 17025 or at factory calibrations (WCS) in Reference to ISO 10012 Calibration certificate in German and English Calibration type force DAkkS ISO 376, 8 steps Calibration power <= 1 MN Of load power tension and compression Number of measuring bridges Power Easy Bridge TEDS TEDS programming without programming)
Calibration of the measured variable torque according HBM standard (Without connector or coupling assembly. Traceability through accreditation ISO 17025 (DKD) guarantees In DAkkS / DKD - calibrations optionally by: DIN 51309, EURAMET / cg-14, VDI2646 (Teilbereichskal. Not possible) DKD-R 3-5 (turning moment), or DKD-R 3-7 (transfer torque wrench). Factory calibrations (WCS) in relation to ISO 10012th Calibration certificate in German and English Calibration type torque WKS, 6 steps, 1 + 1 measurements Measuring range <= 200Nm Load direction right and left Moment Number outputs an output signal TEDS TEDS programming without programming 1. Signal output mV / V 2. Signal output 0
Calibration of the measured variable torque according HBM standard (Without connector or coupling assembly. Traceability through accreditation ISO 17025 (DKD) guarantees In DAkkS / DKD - calibrations optionally by: DIN 51309, EURAMET / cg-14, VDI2646 (Teilbereichskal. Not possible) DKD-R 3-5 (turning moment), or DKD-R 3-7 (transfer torque wrench). Factory calibrations (WCS) in Terms of ISO 10,012th Calibration certificate in German and English Calibration type torque WKS, 6 steps, 1 + 1 measurements Measuring range <= 10kNm Load direction right and left Moment Number outputs an output signal TEDS TEDS programming without programming 1. Signal output mV / V
technology özllkler ksmnda blgi was
Absolute Pressure Measuring system: strain gauge 350 Ohm
(K-RTNaa / bbb cccc dd eee Compact RTN load cell as a variant in special design DMS-measuring system (4000 ohms), nominal characteristic value 2.85 mV / V, with fixed cable, free ends, IP68 protection to EN 60,529th design standard Accuracy class C3 Rated load 150t Explosion protection No explosion Cable length 12m Others without TK0 without Country / customer default Creep 20 ° C Standard)
3-way rosette 1.5, 350 OHM LUK / SENSOR / 3Set floors form
